First published online January 12, 2004
Journal of Experimental Biology 207, 587-596 (2004)
Published by The Company of Biologists 2004
doi: 10.1242/jeb.00793
Mechanical work and muscular efficiency in walking children
B. Schepens,
G. J. Bastien,
N. C. Heglund and
P. A. Willems*
Unité de Physiologie et Biomécanique de la Locomotion,
Université Catholique de Louvain, 1 Place Pierre de Coubertin, B-1348
Louvain-la-Neuve, Belgium

View larger version (23K):
[in a new window]
|
Fig. 1. Fluctuations of the external and internal mechanical energy during one
stride of walking. The three upper curves present the mechanical energy
changes of the centre of mass of the body (COM):
Ek is the kinetic energy due to its velocity relative to
the surroundings, Ep is the potential energy and
Eext is the external energy, which is the sum of the
Ek and Ep curves. Due to a
pendular-like energy transfer between Ek and
Ep, the variations of the Eext curve
are smaller than those of the Ek and
Ep curves. The increment a represents the work
done on the COM during the first double contact phase of the stride.
The internal work (Wint,dc) made by one leg against the
other is presented as a function of time in the fourth and fifth curves: the
positive work done by the back leg during the first double contact phase
(increment b) is equal to the negative work (decrement d)
absorbed in the front leg. The
and
curves are the kinetic
energy changes of the lower and upper limbs, respectively, due to their
velocity relative to the COM. The increment c represents the
positive work to accelerate the front lower limb during the double contact
phase. The internal energytime curve of the lower limb
( ) is the sum of the
and
Wint,dc curves. This procedure assumes that the internal
positive work done by the back leg during the double contact phase (increment
b in Wint,dc) increases passively the backward
velocity of the front leg relative to the COM (see Materials and
methods). Consequently, the internal work done by the front leg is reduced
(increment e in
). The `stick-man' at the
bottom of the figure shows the position of the limb segments each 10% of the
stride: thick lines refer to the segments on the right side of the body that
were recorded by infrared cameras; thin lines refer to the segments of the
left side of the body that were reconstructed on the assumption that the
movements of the left segments during one half-stride were equal to the
movements of the right segments during the other half-stride. The vertical
broken lines delimit the two double contact phases of the stride and were
determined from the force traces. The curves are from a 20-year-old woman
(mass, 70.1 kg) walking at 1.5 m s1.
|
|

View larger version (34K):
[in a new window]
|
Fig. 3. Energy recovery and mass-specific mechanical work per unit distance as a
function of walking speed in different age groups. The pendular recovery of
mechanical energy defined by equation
1 (R; circles) and by
equation 2
(Rc; crosses) and the external work
(Wext) are presented in the two upper rows. The internal
work done by one leg against the other (Wint,dc) is
presented in the third row. The kinetic internal work
(Wint,k; fourth row) is measured, allowing energy transfer
between the segments of the same limbs but not between limbs. The internal
work (Wint; fifth row) is measured, allowing energy
transfer between Wint,dc and Wint,k
(see Materials and methods). The bottom row shows the total work
(Wtot=Wext+Wint).
The broken lines represent the weighted mean of the adult data (other
indications are as in Fig. 2).
Note that above 1 m s1, Wext,
Wint and Wtot are greater in children
than in adults; these differences are greater the younger the subject and tend
to disappear after the age of 10.
|
|

View larger version (18K):
[in a new window]
|
Fig. 5. Contribution of external and internal power to the total mechanical power
spent during walking. In each age group, the mass-specific external power
( Wext), internal power
( int) and total power
( tot) are presented as a
function of the walking speed. For
tot, the solid line
represents the total mechanical power based upon
equation 4, which allows
reasonable energy transfers (see Materials and methods). The lower broken line
shows the total mechanical power computed as the sum of
ext and
int,k (as has been done in
the past). The upper broken line shows the total mechanical power based upon
equation 5, which does not allow
any energy transfers between
ext,
int,kand
int,dc. Lines represent the
weighted mean of the data (KaleidaGraph 3.6). Note that at low speeds,
ext is greater than
int.
|
|
© The Company of Biologists Ltd 2004